How to Prepare Your Freshly-Caught Lobster

First consider the size of your pot for boiling the lobsters. An 8-quart pot will easily take one lobster, a 16-quart pot, 2 or 3 lobsters. If you are cooking a lot of lobsters you’ll either need to cook them in stages or have more than one pot of water boiling.

Should you remove the bands that are holding the lobster claws closed? By all means keep the bands on while you are storing the live lobsters. Some people take them off right before dropping them in the pot because they say that the rubber imparts an off taste to the lobster if you leave them on. I’m somewhat of a scaredy-cat (and I value my fingers) so I usually leave them on. If you are cooking lobster for the first time, I recommend keeping the bands on.

1 Bring a large pot of salted water to a boil: Fill a large pot 3/4 full of water. Add a tablespoon of salt for every quart of water. The water should be salty like sea water (in fact you can use clean sea water if you have it). Bring the water to a rapid boil.

2 Lower the lobsters into the pot: Grasp the lobster by the body and lower it upside down and head first into the boiling water. Continue to add the live lobsters to the pot in this manner. Cover the pot.

Put the lobster head first into boiling salted water

3 Boil lobsters for 10 to 20 min, depending on size: Note the time at which the water comes to a boil again. From that point, boil the lobsters for 10-20 minutes or longer, depending on the size of the lobster. 10-13 minutes for 1 lb lobster, 12-18 minutes for a 1 1/2 pound lobster, 18-23 minutes for a 2-3 pound lobster. The lobsters should be a bright vivid red color when done.

Note that larger lobsters will turn bright red before they are completely finished cooking, so you do want to time your cooking, and not just go on color alone.

Unlike with fresh scallops or fish that you can eat raw (think sashimi), you don’t want to eat raw or undercooked lobster. Translucent undercooked lobster meat really doesn’t taste good. It needs to be opaque through and through. If you cook it too long, the meat will get rubbery, so keep an eye on the time.

4 Remove lobsters from pot to drain: Remove the lobsters from the pot with tongs and place on a plate to drain and cool.

How to Eat Lobster

What you’ll need: Before you get started, you’ll want to assemble some essentials. You’ll need a nutcracker, a large bowl to hold the shells, a small dipping bowl for melted butter, and what’s missing from the following photograph—a lot of napkins!

How to Eat Lobster

Eating lobster is messy, you’ll need napkins. There’s a good reason they give diners plastic bibs at restaurants when serving lobster.

You may also want to use some kitchen shears and nutpicks in addition to a nutcracker.

After the lobster comes out of the pot, let it cool for a few minutes, otherwise it will be too hot to handle.

Start with the claws: Pull off the rubber bands from the claws, if they are still attached. Twist the claws away from the body at the joints that connect them to the body. Separate the knuckle from the claw.

Separate the lobster claw from the joints

Pull back the “jaw” of the claw until it breaks, but do it gently, so that the little bit of meat that is in the small part of the jaw stays attached to the rest of the meat (it’s easier than trying to fish it out of the small shell).

Pull off the small end of the claw
If you do it gently, the meat will be revealed

Use a nut cracker to crack the main claw shell. Depending on the season and the size of your lobster, the shell may be easy or hard to crack with a nutcracker. If necessary you can take a mallet or hammer to it, but do it gently, just enough to break the shell without crushing the meat inside.

Use a nutcracker to break the claw shell
Peel away the shell pieces to reveal the meat

Pull away the broken shell pieces and pull out the meat inside. Any white stuff attached to the meat is fat, which you can choose to eat or not. Dip into melted butter or not, and eat.

Extract meat from the knuckles: Use kitchen shears (if you have them) to cut the knuckle shell along its length. Pry open the shell where you made the cut and you can pull out all the knuckle meat in one piece.

Use scissors or a nutcracker to break open the lobster joints
The lobster meat will be revealed

Alternately, you can crack each section of knuckle with a nutcracker and pull the meat out in chunks.

If you have a very large lobster, you can eat the legs. Get to the meat from the legs in a way similar to pulling off the “jaw” of the claw.

Bend the joints of the legs the “wrong” way, which breaks them. You should have a piece of meat attached. Simply bite this off, leaving a thin piece of cartilage attached to the rest of the leg.

Go for the tail: Now on to the lobster tail, where the biggest piece of meat lies. You’ll need both hands to get the meat from the tail. Grip the lobster’s body with one hand and the tail with the other. Bend the tail back away from the body to separate it from the body.

Grasp the lobster tail with one hand and the body with another
Pull back and twist to remove the tail from the body

You will see one, and maybe two, odd things inside. You’ll see the greenish “tomalley,” which is the lobster’s liver. You can choose to eat it or not. Some people spread it on toast or add it to lobster soups or sauces.

If the lobster is a female, you may also see the bright red “coral,” which is the roe of the lobster. You may also choose to eat this or not. The coral can be spread on toast as well, or used to add flavor to lobster bisque.

The tail will now look like a really big shrimp. Grab the flippers at the end of the tail and bend them backwards gently. If you do it right, you’ll get the meat from the inside of one or more flippers.

Grasp the end of the lobster tail with one hand, and the rest of the tail with the other
Pull back the end of the lobster tail to separate it from the rest of the tail

This is uncommonly sweet meat, so don’t forget the morsels in the flippers! You can pry them out by working the little joints back and forth, or use shears to cut their thin shells.

With the flippers off the tail, you can now just put your finger through the small opening where the flippers were and push the tail meat out in one piece. If you have an exceptionally large lobster, use kitchen shears to cut a line down the underside of the tail to help remove the meat.

Use your finger to push the lobster meat from the small end of the tail out the big end
Pull out the lobster tail meat

Remove the digestive tract: Before you eat the tail, pull the top of it off. This will reveal a digestive vein which you will likely want to remove, much like deveining a shrimp. It won’t hurt you if you eat it, but it is the digestive tract of the lobster.

Pull back the flap at the big end of the tail to reveal the digestive canal
Use your fingertips to remove the digestive canal from the tail

There is meat inside the body of the lobster, mostly right around where you pulled off the tail. For lobsters bigger than 2 pounds it is worth it to fish around for these extra morsels.

There you go! Now just dip in melted butter (or not) and eat. If you have crusty bread, it tastes great dipped in the lobster-infused butter as well.

All credit for these delicious tips goes to Simply Recipes. https://www.simplyrecipes.com/recipes/how_to_boil_and_eat_lobster/

This entry was posted in Eats, Featured and tagged , , . Bookmark the permalink.